Knowledge

Powder coating identification method

1. Appearance identification method:

1. The hand feeling is smooth, fluffy and floating like silk. The hand feels rough, heavy, and heavy. Grab a handful of powder in your hand, the smoother and fluffier the powder is, and the quality is better. On the contrary, the rough powder feels heavy and the quality is Poor. It is not easy to spray, and there is a lot of secondary powder falling, which is a big waste.

2. The larger the volume, the less filler in the powder coating, the higher the cost. The better the powder quality. The smaller the volume, the higher the filler in the powder coating, the lower the cost. The worse the powder quality. The same carton, see The powder of which one has a large volume is a good powder, and the other one has a small volume and is a poor powder. It is not easy to spray, more secondary powder falls, a large waste, less spraying area, and high cost of use.

3. The powder with good storage time can be stored for a long time, and the leveling and other effects of the powder remain unchanged. The poor powder cannot be stored for a long time, and the leveling and other effects of the poor powder will become worse after 3 months. The shelf life is 12 months at room temperature, and the quality of low-end raw materials is unstable and easy to deteriorate. Using poor raw materials to produce powder, the sprayed surface will accelerate pulverization and aging after half a year. It will affect the customer's reputation. In addition, the powder is not easy to store, and the customer Large waste of powder and high billing fee

2. Spraying area identification method:

The resin content of the normal powder spraying area should be about 55-65%, the resin is about 20 yuan/KG, and the filler is about 2 yuan. Some bad powder factories use less than 45% resin content to shoddy , increase the filler to reduce the cost and reduce the spraying area. Comparison method: two same powders spray the same product, see which one has more powder sprayed products, which one has less sprayed products, and the one with less sprayed products is poor, and the cost of use High. For the manufacturer, the spraying area is small, and the cost of use is high. Calculated on the basis of 6 square meters per kilogram of powder spraying, each less spraying of one square meter is equivalent to an extra payment of 3-6 yuan per kilogram of powder for the manufacturer. It is recommended to use the manufacturer Use genuine powder, carefully calculate your actual use cost

Three. Spraying personnel job identification method:

Powder coating rate, good working efficiency powder is easy to spray, spraying 1-3 guns can cover the substrate, secondary recovery of powder is less, high work efficiency. Poor powder is not easy to powder, spraying 3-5 guns is enough The substrate can be covered, and there is a lot of recycled powder, which leads to low work efficiency. The operator can determine whether the amount of powder dropped is too much or not by spraying the powder rate. The output of the product is less at the same time, and the secondary recycled powder is more, increasing the operation Manpower burden and low work efficiency.

Four. Baking identification method:

Is there any smoke produced? Good powder does not produce a lot of smoke during the baking process. Poor powder produces a lot of smoke during the baking process. Good powder raw materials do not produce a lot of smoke, and some manufacturers use inferior raw materials to charge Good material. The amount of powder will increase, the number of squares can not be sprayed, and the cost of use will be increased. The same amount of powder will produce less products.

5. Appearance and gloss identification method of finished product after baking:

The powder products with good appearance after baking are fine, full, transparent and have a strong three-dimensional effect. The powder products with poor appearance are dull, dull, foggy, opaque, and poor in three-dimensional effect. Compare and observe the two boards Poor appearance will affect customer reputation and affect product appearance. Powder with good gloss has good gloss and can maintain relative gloss for a long time. Powder with poor gloss has good effect when it is just baked, and it will start to sagittal after a few months. The powder made of materials with poor gloss appearance inspection cannot maintain long-term gloss stability, and there will be sagittal light, chalking, paint peeling, etc.

Six. Adhesion and aging identification method:

Adhesion and aging Good powder has strong adhesion and toughness, and can keep for several years without pulverization and aging. Poor powder has poor adhesion and is very brittle, and it will begin to age and pulverize 3 months to half a year after spraying. Contrast test adhesion and bending, and observe whether the product is aging or powdering after a few months. Poor adhesion and aging, the product is prone to aging, powdering, rusting, shortening the service life of the product, and affecting customer reputation

Seven. High temperature identification method:

High temperature, adjust the temperature to 220-230 degrees, and keep warm for 10-15 minutes. Good powder has better temperature and weather resistance. After baking at high temperature, the color change is small and the gloss does not change much. Poor, serious discoloration and dull luster after high temperature baking. This method is especially effective for detecting outdoor light-colored powders. Poor powders use poor resins, titanium dioxide, poor pigments and fillers, and have poor temperature and weather resistance. Low cost, shoddy.

Eight. Environmental protection identification method:

SGS environmental protection testing Good powder materials are produced by large factories, and the environmental protection is guaranteed. Poor materials and recycled powder, there is no way to ensure that the environmental protection does not exceed the standard for a long time. Environmental protection SGS testing The environmental protection exceeding the standard has caused great economic losses to some export companies.

Nine. Analysis of the current situation of powder coatings:

Powder coating is a processing consumable product, the investment threshold is relatively low, and the market competition is fierce, which has also caused chaos in the powder coating market. The phenomenon of cutting corners is serious, and the pursuit of short-term interests has caused a relatively large impact on some genuine companies. The paint is a powdery substance, which is not easy to identify, and has caused relatively large economic losses to some powder-using companies. Originally, the actual amount of the product was 3 tons, and the price was cheap through the use of fake materials. The amount of powder was increased to 4-5 tons. On the contrary, it increases the cost of powder-using enterprises. Most of the powder-consuming enterprises only care about the price of powder, not the actual cost of use, which causes great losses to the enterprises.


You Might Also Like

Send Inquiry